Everyone maintains their own individual theory in relation to How to Install a Bathtub.
Installing a bath tub isn't precisely brain surgery, however it does call for strong plumbing, carpentry, and also sometimes, tiling abilities. Changing an old bathtub with a new one is also a moderately difficult project. If the old tub is easily easily accessible, the task can move quickly; if you need to open up a wall to eliminate the old bathtub and also position the new bathtub, the task is much harder. In either situation, the task is within a residence handyman's abilities, although you will need a helper to leave the old bathtub and set in the new one. Ensure you have qualified yourself for the task as well as fit trying it. As opposed to hiring a professional to take over a halfway-completed job, it is far better to consider using one prior to you start. Opportunities are you might require an expert plumber to make tube links.
This post will certainly assist you set up a new bathtub in your washroom if you have already acquired a brand-new tub and don't require to alter the plan of your previous supply of water pipes.
Your devices as well as material checklist should consist of the following:
Getting ready for the Installation
To start with, the sustaining frame supplied with the bathroom ought to be fitted (if required) according to the supplier's directions. Next, fit the faucets or mixer to the bathtub. When suitable the faucet block, it is very important to ensure that if the tap includes a plastic washer, it is fitted in between the bathroom as well as the taps. On a plastic bathroom, it is additionally practical to fit a supporting plate under the taps device to avoid strain on the bath tub.
Fit the adaptable tap connectors to the bottom of both faucets using 2 nuts and also olives (sometimes provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and then pass the electrical outlet with the hole in the bath. Make use of the nut provided by the manufacturer to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the adaptable overflow pipe to the overflow outlet. Afterwards, screw the pipe to the overflow face which need to be fitted inside the bath. Make sure you use every one of the supplied washing machines.
Link the trap to the bottom of the waste electrical outlet on the bathtub by winding the string of the waste outlet with silicone mastic or PTFE tape, and also screw on the trap to the electrical outlet. Link the bottom of the overflow tube in a comparable manner.The bath must now prepare to be fitted in its last position.
Removing Old Taps
If you require to replace old taps with brand-new ones as a part of your setup, after that the first thing you ought to do is separate the supply of water. After doing so, activate the taps to drain pipes any type of water continuing to be in the system. The process of getting rid of the existing taps can be fairly problematic due to the limited accessibility that is typically the case.
Utilize a container wrench (crowsfoot spanner) or a tap device to reverse the nut that connects the supply pipes to the faucets. Have a towel ready for the remaining water that will certainly originate from the pipes. When the supply pipelines have been eliminated, make use of the same device to loosen up the nut that holds the taps onto the bath/basin. You will certainly require to stop the solitary faucets from transforming during this procedure. As soon as the taps have actually been removed, the holes in the bath/basin will certainly have to be cleaned up of any old securing substance.
Prior to moving on to fit the new taps, contrast the pipeline connections on the old taps to the brand-new faucets. If the old taps are longer than the new faucets, after that a shank adapter is required for the new faucets to fit.
Mounting the Bathtub
Using both wood boards under its feet, position the bathtub in the needed setting. The wood boards are practical in evenly spreading the weight of the tub over the location of the boards as opposed to concentrating all the weight onto 4 tiny factors.
The next goal is to make sure that the bath tub is leveled all round. This can be attained by checking the spirit level as well as changing the feet on the tub till the level reviews level.
To install taps, fit the bottom of the furthest versatile faucet adapter to the ideal supply pipeline by making a compression sign up with; after that do the very same for the other tap.
Switch on the supply of water as well as inspect all joints as well as brand-new pipework for leaks and tighten them if required. Fill the tub and likewise inspect the overflow outlet as well as the typical outlet for leaks.
Finally, repair the bath paneling as described in the producer's instruction manual. Tiling and sealing around the bathtub should wait until the bathtub has actually been made use of at the very least when as this will certainly resolve it right into its final position.
Fitting New Taps
If the tails of the brand-new faucets are plastic, then you will require a plastic adapter to stop damages to the string. One end of the port fits on the plastic tail of the tap and the various other end gives a link to the existing supply pipes.
If you need to fit a monobloc, then you will certainly call for minimizing couplers, which links the 10mm pipe of the monobloc to the basic 15mm supply pipe.
Next off, place the tap in the placing hole in the bath/basin ensuring that the washing machines remain in place in between the tap and the sink. Safeguard the tap in place with the manufacturer given backnut. When the tap is safely in place, the supply pipelines can be linked to the tails of the faucets. The faucets can either be connected by utilizing corrugated copper piping or with normal faucet ports. The previous kind should be connected to the faucet finishes first, tightening up just by hand. The supply pipes can later on be linked to the other end. Tighten up both ends with a spanner after both ends have actually been connected.
Tiling Around the Bath tub
In the area where the bath fulfills the ceramic tile, it is necessary to secure the joins with a silicone rubber caulking. This is important as the installation can relocate enough to fracture a stiff seal, causing the water to permeate the wall surface in between the bath and the tiling, leading to difficulties with moisture as well as possible leakages to the ceiling below.
You can pick from a range of coloured sealers to blend in your components and installations. They are sold in tubes and also cartridges, and can sealing voids as much as a size of 3mm (1/8 inch). If you have a larger void to fill, you can load it with twists of drenched newspaper or soft rope. Keep in mind to constantly fill up the bath tub with water before securing, to allow for the motion experienced when the bathtub is in usage. The sealant can break relatively very early if you do not take into consideration this activity before securing.
Alternatively, ceramic coving or quadrant ceramic tiles can be made use of to border the bath or shower tray. Plastic strips of coving, which are easy to use and also cut to size, are additionally easily offered on the marketplace. It is recommended to fit the ceramic tiles using water-resistant or water-proof adhesive as well as cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I was guided to that article on A Step-by-Step Guide to Installing a Bathtub from someone on a different site. If you appreciated our blog post please remember to share it. Thanks a lot for your time. Kindly stop by our site back soon.
Schedule Here